Call us with any questions! 028 8675 2336

Ergovent RONDO Invisible Ceiling Air Valve Diffuser – 160mm

£60.99

Frameless plaster-in ceiling air valve for 160mm ductwork. Only a thin ring-shaped air slot shows after painting.

  • Ceiling cut-out: 300mm
  • Plasterboard: 13mm to 26mm, one or two layers
  • Supply or extract air, balancing valve included
  • Fits metal, flexible or 75/90mm plastic duct systems

Ergovent Rondo 160mm plaster-in ceiling diffuser (frameless, 300mm cut-out)

The Ergovent Rondo 160mm is a plaster-in air valve for 160mm ducts. It is an invisible ceiling diffuser made of gypsum and plastered into a plasterboard ceiling. Only a thin ring-shaped air slot shows after the ceiling is skimmed and painted. It works for supply and extract air.

The Rondo 150mm and 160mm share the same 300mm ceiling cut-out and body. Only the duct connection differs. Ergovent calls the Rondo a frameless ventilation diffuser: there is no grille, frame or visible edge once the ceiling is finished.

Rondo 160mm specification

Specification Rondo 160mm
Duct connection 160mm
Ceiling cut-out 300mm diameter
Face diameter 296mm
Body width 296mm, plus two plaster mesh fixing tabs of 38mm x 173mm
Overall height 91mm: 50mm body and a 41mm duct spigot
Plasterboard thickness 13mm to 26mm, one or two layers
Air direction Supply and extract
Balancing valve Included: polyurethane damper with settings D0 to D7
Material Gypsum (plaster), paintable
Manufacturer Ergovent
Recognition Red Dot 2023 winner

Dimensions are in the shared Rondo 150/160 data sheet. Its supply, extract and velocity charts cover the Rondo 150mm only. Ask us for Rondo 160mm airflow figures before you specify it.

Where the Rondo 160mm is used

The Rondo is specified where a visible grille would spoil the ceiling. Typical projects include:

  • Luxury homes and new builds
  • Architect-designed houses and high-end apartments
  • Boutique hotels
  • Contemporary offices
  • Interior-led commercial spaces

Inside those projects it suits bedrooms, living spaces, offices and hotel rooms. In bathrooms and other humid rooms, finish it with a moisture-resistant primer and ceiling paint, as the finishing section below explains.

What you need to install the Rondo 160mm

You need the Rondo, a duct to connect it to, and the materials to finish the ceiling around it. Ergovent's Rondo installation manual shows the steps for every size.

  • The Rondo 160mm, supplied with its balancing valve
  • A 160mm duct, or 75mm or 90mm flexible plastic ducts with a connection box
  • A plasterboard saw or cutter for the 300mm hole
  • A spirit level, and a drill with screws for the mesh fixing tabs
  • Mounting tape, if the Rondo needs holding in place before the boards go up
  • Primer, joint filler, thin glass fabric and ceiling paint for the finish

Which installation method suits your duct?

The installation method depends on the duct system and on whether the plasterboard is already up. Ergovent gives four methods.

Method and duct How it connects Ceiling stage
1. Metal ducts Through a soft flexible duct Boards already up; hole cut in them
2. Metal ducts Directly into the metal duct Duct set to height, then the boards go up
3. Flexible plastic ducts, 75mm or 90mm Into the connection box tube Before the boards go up
4. Any duct system Onto a solid duct After the boards are up

Frameless diffusers need slightly more space above the ceiling than framed ones. For methods 2 and 3 the manual sets the duct end 4.5cm above the ceiling line for one layer of plasterboard and 3.5cm for two layers. As drawn in the manual, keep the vertical duct at least 8cm from the ceiling framing, and keep the horizontal duct run at least 7cm above the ceiling with one layer of plasterboard or 6cm with two. For method 4, leave at least 8.5cm of straight duct between the ceiling and any bend, then trim the duct to 5.5cm as the manual shows.

Fitting the Rondo 160mm, step by step

These steps follow installation method 1, for metal ducts with a flexible connection.

  1. Cut a 300mm hole in the plasterboard.
  2. Cut a small notch at the edge of the hole, as shown in the manual.
  3. Pull the flexible duct through the hole.
  4. Fit the duct over the Rondo's 160mm spigot and secure it with a duct clip.
  5. Tilt the Rondo up through the hole so the mesh tabs rest on top of the board.
  6. Level it so its face sits about 1mm below the plasterboard.
  7. Screw up through the plasterboard into the mesh tabs.

The manual shows one-layer and two-layer fitting for each method.

How to finish the ceiling around the Rondo 160mm

The finish decides whether the Rondo stays invisible. Ergovent recommends the Knauf finishing system:

  1. Remove dust from the surfaces and gaps you will fill.
  2. Prime with Ceresit CT-17 or Knauf Tiefgrund.
  3. Fill the gaps with Knauf Fugenfuller or Uniflott filler.
  4. Cover the whole diffuser surface with thin glass fabric so the joint does not crack.
  5. Apply a deep primer over the filled areas before painting.
  6. Paint the ceiling and the Rondo's outer ring together.
  7. Paint the removable centre plate separately, then refit it.

In humid rooms use a moisture-resistant primer and a ceiling paint made for humid rooms.

Which Rondo size do you need?

Choose the Rondo that matches your duct diameter. The Rondo 160mm uses the same 300mm ceiling cut-out as the Rondo 150mm.

Model Duct Ceiling cut-out
Rondo 100mm 100mm 242mm
Rondo 125mm 125mm 242mm
Rondo 150mm 150mm 300mm
Rondo 160mm (this page) 160mm 300mm

The Rondo 100mm and 125mm have a 238mm face, stand 89mm high and won the Design Plus award in 2023. The Rondo 150mm and 160mm have a 296mm face, stand 91mm high and won a Red Dot award in 2023.

How to balance airflow on the Rondo 160mm

Each Rondo comes with an Ergovent balancing valve: a polyurethane damper inserted in the diffuser's connection sleeve. You balance the system by changing the number of removable segments. On the Rondo 150mm and 160mm, settings D1 to D3 add segments, then D4 to D7 close the four-segment damper from full open to 25% open.

Setting Damper (Rondo 150 and 160) Airflow
D0 No damper Fully open
D1 1 segment Reduced
D2 2 segments Reduced further
D3 3 segments Reduced further
D4 4 segments, full open Reduced further
D5 4 segments, 75% open Reduced further
D6 4 segments, 50% open Reduced further
D7 4 segments, 25% open Lowest

Ergovent publishes these charts for the Rondo 150mm. Ask us for Rondo 160mm data before you balance a system.

Rondo or Kvadro?

Choose the Rondo for a round ring in the ceiling and the Ergovent Kvadro for a square outline. Both give the same flush plaster-in finish.

See the Ergovent Kvadro range.

Rondo 160mm questions

Can the Rondo 160mm be fitted to an existing ceiling?

Yes, if the ceiling is plasterboard and a duct already reaches the spot. Method 1 suits a flexible duct you can pull through the 300mm hole. Method 4 suits a solid duct that already passes through the board: you trim it, fit the Rondo, turn it 90 degrees and glue the cut-out board pieces back over the fixing tabs. Then fill, prime and repaint the area. It is easiest to plan in at the ceiling stage.

Does the Rondo work for extract as well as supply?

Yes. Ergovent publishes supply and extract charts for the Rondo 150mm; ask us for the 160mm figures.

Can I paint the Rondo?

Yes. The gypsum body takes the same primer and paint as the ceiling.

Will it fit a double-layer ceiling?

Yes. The Rondo suits plasterboard from 13mm to 26mm thick, in one or two layers.

Can I use it with a 75mm or 90mm plastic duct system?

Yes. Installation method 3 connects the Rondo to 75mm or 90mm flexible plastic ducts through a connection box.

How do I adjust the airflow after fitting?

Take off the removable centre plate, change the damper segments in the connection sleeve, then refit the plate. Settings run from D0 with no damper to D7 at 25% open.

We supply ventilation products across the UK and Ireland. Need help choosing? Call 028 8675 2336 or email sales@freshairsupplies.co.uk.